<address id="rb75h"></address>

      <sub id="rb75h"></sub>

            <sub id="rb75h"></sub>

            欢迎访问温州市旭日印刷机械有限公司官网!

            搜索
            您当前所在位置:网站首页 > 常见问题 > 切角机常见问题
            公司产品远销国内外,在市场上有较高的信誉与知名度
            PJQ-100型切角机维护保养

            发布时间:2019-10-21

            来源:温州市旭日印刷机械有限公司

            浏览次数:67

              为了延长机器的使用寿命,保证机器能顺利工作,正确地维护、保养机器是至关重要的。

              1操作者应定期检查机器的各部件是否正常,各油孔是否有堵塞现象,并应及时排除故障。

              2应于各铜套、活动面经常加注润滑油,使机器保持良好的润滑状态。

              3切刀要保持锋利,用钝刀裁切即要缩短机器的使用寿命又不能裁出理想的成品。

              4工作台上不要放扳手、螺丝刀等硬物,要经常擦拭机器使机器保持清洁、干净。

              The distribution of lubrication points is shown in Figure 3.

              In order to extend the service life of the machine and ensure that the machine can work smoothly, it is crucial to properly maintain and maintain the machine.

              4.1 The operator shall regularly check the regularity of the parts of the machine and the blockage of the oil holes and shall promptly troubleshoot them.

              4.2 The copper sleeves and movement surfaces shall be lubricated regularly to maintain the machine in good lubrication condition.

              4.3 To keep sharp, cutting with a blunt knife reduces the service life of the machine and does not produce the desired finished product.

              4.4 Do not put a wrench, screwdriver and other hard things on the platform. Always wipe the machine to keep it clean.

              Δ注意事项:

              1.必须在?;刺碌髡?。

              2.工作时,手远离切刀。

              3.机台的轴,每月加注润滑油一次

              4.非本机操作人员禁止操作本机。

              ΔNotes:

              1. Must adjust the platform under downtime.

              2. Keep your hands away from the cutter while working.

              3. The shaft of the platform is lubricated once a month

              4. Non-native operators are prohibited from operating this machine.

              图(3)传动原理示意图

              Figure(3) A schematic diagram of transmission principle

            润滑点

             Lubrication point

            推荐润滑油 

            Recommended lubricants

            加油次数 

            Number of refuels

            备注 

            Remarks

            1

            40#机油 

            Engine oil

            每天一次 

            Once a day.

            拖板活动面 

            Drag board active surface

            2

            40#机油 

            Engine oil

            每天一次 

            Once a day.

            连杆下关节 

            Sublink joint

            3

            40#机油 

            Engine oil

            每天一次 

            Once a day.

            连杆上关节 

            Connecting rod upper joint

            4

            40#机油

             Engine oil

            每天一次 

            Once a day.

            偏心轮轴孔 

            Eccentric shaft hole

            5

            40#机油 

            Engine oil

            每天一次 

            Once a day.

            开关座活动面 

            Switch seat active surface

            6

            40#机油 

            Engine oil

            每天一次 

            Once a day.

            飞轮轴孔 

            Flywheel shaft hole

            我是分类列表
              问题详情
              摇钱树捕鱼游戏平台 285| 714| 927| 984| 654| 528| 762| 597| 201| 207| 246| 678| 723| 381| 243| 795| 39| 303| 375| 198| 738| 390| 345| 18| 960| 837| 96| 690| 81| 90| 60| 90| 441| 240| 498| 153| 360| 147| 867| 306| 534| 618|